12-20-2024, 08:17 PM
<h2> Employing the Balanset-1A System </h2>
<h3> Equipment Preparation </h3>
<ul>
<li> vibration sensors, optical speed sensor, magnetic base, software package, and included accessories. </li>
<li> Connect the device to your PC using the USB interface and confirm the software installation. </li>
</ul>
<h3> Mounting the Sensors </h3>
<ul>
<li> Mount the vibration transducers securely on the machine's housing where vibrations are most pronounced, typically near the bearings. </li>
<li> Aim the optical rpm sensor at the rotating shaft and apply a reflective strip to the shaft for phase angle data acquisition. </li>
</ul>
<h3> Software Startup </h3>
<ul>
<li> Open the Balanset application on your PC. </li>
<li> Select the appropriate balancing mode: single-plane or two-plane, depending on the rotor type and your specific requirements. </li>
</ul>
<h3> </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" alt="2-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Operate the rotor at its intended working speed. </li>
<li> The software will measure the vibration level, rotational speed, and phase angle. This data establishes the current imbalance condition. </li>
</ul>
<h3> Attaching the Trial Weight </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" alt="3-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Halt the rotation and mount a test weight at a designated position on the rotor, with the weight's value entered into the software (usually in grams). </li>
<li> Run the rotor again, allowing the software to measure the effects of the trial weight on vibration and phase. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" alt="5-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<h3> Determining the Corrective Mass </h3>
<ul>
<li> Based on the measured data, the software automatically calculates the correction weight parameters: mass and installation angle. </li>
<li> The calculated values are presented on-screen in both numerical and graphical formats. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" alt="Bs1 Manual" style="width: 30%; display: block; margin-bottom: 10px;">
</a>
<h3> Installing the Correction Weight </h3>
<ul>
<li> Mount the calculated corrective weight onto the rotor at the specified location and angle. </li>
<li> You can conduct interim measurements to confirm that the imbalance is decreasing as expected. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" alt="1-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<h3> Verification and Balancing Completion </h3>
<ul>
<li> With the compensating weight attached, operate the rotor and assess the level of any residual vibration. </li>
<li> The balancing procedure is finished if the remaining vibration is within the permissible limits specified in ISO 1940. </li>
<li> Should the vibration still be excessive, repeat the balancing steps, making further adjustments to the corrective weight as needed. </li>
</ul>
<h3> Generating a Documentation of the Balancing Results </h3>
<ul>
<li> All balancing results are logged and archived within the software, from which you can produce a printable report summarizing the vibration levels, compensating weight, and its installation position. </li>
</ul>
<h3> Concluding Steps and Verification </h3>
<ul>
<li> Verify the secure attachment of all balancing weights and measurement sensors. </li>
<li> Ensure the rotor rotates smoothly and without excessive noise. </li>
<li> If the rotor is part of a complex mechanism, verify the proper interaction of all its components. </li>
</ul>
<p> This process allows for precise imbalance correction, reducing vibration and extending equipment life. </p>
Instagram: https://www.instagram.com/vibromera_ou/
Youtube : https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL
Our website about <a href="https://vibromera.eu
"> Air handling unit balancing </a>
Machinio: https://www.machinio.com/listings/983801...n-portugal
Facebook: https://www.facebook.com/marketplace/ite...1228150722
<h3> Equipment Preparation </h3>
<ul>
<li> vibration sensors, optical speed sensor, magnetic base, software package, and included accessories. </li>
<li> Connect the device to your PC using the USB interface and confirm the software installation. </li>
</ul>
<h3> Mounting the Sensors </h3>
<ul>
<li> Mount the vibration transducers securely on the machine's housing where vibrations are most pronounced, typically near the bearings. </li>
<li> Aim the optical rpm sensor at the rotating shaft and apply a reflective strip to the shaft for phase angle data acquisition. </li>
</ul>
<h3> Software Startup </h3>
<ul>
<li> Open the Balanset application on your PC. </li>
<li> Select the appropriate balancing mode: single-plane or two-plane, depending on the rotor type and your specific requirements. </li>
</ul>
<h3> </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" alt="2-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Operate the rotor at its intended working speed. </li>
<li> The software will measure the vibration level, rotational speed, and phase angle. This data establishes the current imbalance condition. </li>
</ul>
<h3> Attaching the Trial Weight </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" alt="3-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Halt the rotation and mount a test weight at a designated position on the rotor, with the weight's value entered into the software (usually in grams). </li>
<li> Run the rotor again, allowing the software to measure the effects of the trial weight on vibration and phase. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" alt="5-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<h3> Determining the Corrective Mass </h3>
<ul>
<li> Based on the measured data, the software automatically calculates the correction weight parameters: mass and installation angle. </li>
<li> The calculated values are presented on-screen in both numerical and graphical formats. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" alt="Bs1 Manual" style="width: 30%; display: block; margin-bottom: 10px;">
</a>
<h3> Installing the Correction Weight </h3>
<ul>
<li> Mount the calculated corrective weight onto the rotor at the specified location and angle. </li>
<li> You can conduct interim measurements to confirm that the imbalance is decreasing as expected. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" alt="1-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<h3> Verification and Balancing Completion </h3>
<ul>
<li> With the compensating weight attached, operate the rotor and assess the level of any residual vibration. </li>
<li> The balancing procedure is finished if the remaining vibration is within the permissible limits specified in ISO 1940. </li>
<li> Should the vibration still be excessive, repeat the balancing steps, making further adjustments to the corrective weight as needed. </li>
</ul>
<h3> Generating a Documentation of the Balancing Results </h3>
<ul>
<li> All balancing results are logged and archived within the software, from which you can produce a printable report summarizing the vibration levels, compensating weight, and its installation position. </li>
</ul>
<h3> Concluding Steps and Verification </h3>
<ul>
<li> Verify the secure attachment of all balancing weights and measurement sensors. </li>
<li> Ensure the rotor rotates smoothly and without excessive noise. </li>
<li> If the rotor is part of a complex mechanism, verify the proper interaction of all its components. </li>
</ul>
<p> This process allows for precise imbalance correction, reducing vibration and extending equipment life. </p>
Instagram: https://www.instagram.com/vibromera_ou/
Youtube : https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL
Our website about <a href="https://vibromera.eu
"> Air handling unit balancing </a>
Machinio: https://www.machinio.com/listings/983801...n-portugal
Facebook: https://www.facebook.com/marketplace/ite...1228150722